PDF herunterladen
CC BY 4.0 · Organic Materials 2021; 03(02): 214-220
DOI: 10.1055/a-1441-8239
Short Communication

Chain-End Effect for Intermediate Water Formation of Poly(2-Methoxyethyl Acrylate)

S. Nishimura 
a   Institute for Materials Chemistry and Engineering, Kyushu University, 744, Moto-oka, Nishi-ku, Fukuoka 819-0395, Japan
,
T. Ueda 
b   Graduate School of Engineering, Kyushu University, 744, Moto-oka, Nishi-ku, Fukuoka 819-0395, Japan
,
D. Murakami 
a   Institute for Materials Chemistry and Engineering, Kyushu University, 744, Moto-oka, Nishi-ku, Fukuoka 819-0395, Japan
b   Graduate School of Engineering, Kyushu University, 744, Moto-oka, Nishi-ku, Fukuoka 819-0395, Japan
,
M. Tanaka 
a   Institute for Materials Chemistry and Engineering, Kyushu University, 744, Moto-oka, Nishi-ku, Fukuoka 819-0395, Japan
b   Graduate School of Engineering, Kyushu University, 744, Moto-oka, Nishi-ku, Fukuoka 819-0395, Japan
› Institutsangaben Funding Information This work was supported by Grants-in-Aid for Scientific Research (KAKENHI) (JP19H05720 to M. T. and JP20J00282 to S. N.) from the Japan Society for the Promotion of Science (JSPS) and “Dynamic Alliance Open Innovation Bridging Human, Environment and Materials” from the Ministry of Education, Culture, Sports, Science and Technology of Japan (MEXT).
› Weitere Informationen
   Lizenzen und Reprints Alle Artikel dieser Rubrik


Abstract

Intermediate water (IW), which is formed not only by biocompatible polymers such as poly(2-methoxyethyl acrylate) (PMEA), but also by biomacromolecules, plays a key role in determining the biocompatibility of synthetic polymers. In this study, we compare the well-defined linear and cyclic PMEA using differential scanning calorimetry and atomic force microscopy. This study aims to clarify the role of the chain-end effect in IW formation to establish design guidelines for biomaterials.

Key words

intermediate water - hydration state - chain-end effect - poly(2-methoxyethyl acrylate) - cyclic polymers - interfacial structures

Supporting Information

Supporting information for this article is available online at https://doi.org/10.1055/a-1441-8239.


Supporting Information



Publikationsverlauf

Eingereicht: 07. Januar 2021

Angenommen: 08. März 2021

Accepted Manuscript online:
16. März 2021

Artikel online veröffentlicht:
26. April 2021

© 2021. The Author(s). This is an open access article published by Thieme under the terms of the Creative Commons Attribution License, permitting unrestricted use, distribution, and reproduction so long as the original work is properly cited. (https://creativecommons.org/licenses/by/4.0/)

Georg Thieme Verlag KG
Rüdigerstraße 14, 70469 Stuttgart, Germany

 

  • References And Notes

      • 1
    • 1a Tsuruta T. J. Biomater. Sci., Polym. Ed. 2010; 21: 1831
      CrossrefPubMed
    • 1b Brash JL, Horbett TA, Latour RA, Tengvall P. Acta Biomater. 2019; 94: 11
      CrossrefPubMed
      2
    • 2a Tanaka M, Motomura T, Ishii N, Shimura K, Onishi M, Mochizuki A, Hatakeyama T. Polym. Int. 2000; 49: 1709
      CrossrefPubMed
    • 2b Tanaka M, Motomura T, Kawada M, Anzai T, Kasori Y, Shiroya T, Shimura K, Onishi M, Mochizuki A. Biomaterials 2000; 21: 1471
      CrossrefPubMed
    • 2c Fujita K, Nikawa Y, Ohno H. Chem. Commun. 2013; 49: 3257
      CrossrefPubMed
    • 2d Nikawa Y, Tsuzuki S, Ohno H, Fujita K. Aust. J. Chem. 2019; 72: 392
      CrossrefPubMed
    • 2e Okada M, Hara E, Kobayashi D, Kai S, Ogura K, Tanaka M, Matsumoto T. ACS Appl. Bio Mater. 2019; 2: 981
      CrossrefPubMed
    • 2f Tanaka M, Kobayashi S, Murakami D, Aratsu F, Kashiwazaki A, Hoshiba T, Fukushima K. Bull. Chem. Soc. Jpn. 2019; 92: 2043
      CrossrefPubMed
      3
    • 3a Vang SN, Brady CP, Christensen KA, Isler JR, Allen KR. J. Extra Corpor. Technol. 2005; 37: 23
      PubMed
    • 3b Kariya S, Nakatani M, Ono Y, Maruyama T, Ueno Y, Komemushi A, Tanigawa N. Cardiovasc. Interventional Radiol. 2020; 43: 775
      PubMed
      4
    • 4a Sato K, Kobayashi S, Kusakari M, Watahiki S, Oikawa M, Hoshiba T, Tanaka M. Macromol. Biosci. 2015; 15: 1296
      CrossrefPubMed
    • 4b Kobayashi S, Wakui M, Iwata Y, Tanaka M. Biomacromolecules 2017; 18: 3834
      CrossrefPubMed
    • 4c Nishimura S, Ueda T, Kobayashi S, Tanaka M. ACS Appl. Polym. Mater. 2020; 2: 4790
      CrossrefPubMed
    • 4d Sonoda T, Kobayashi S, Herai K, Tanaka M. Macromolecules 2020; 53: 8570
      CrossrefPubMed
      5
    • 5a Damodaran VB, Murthy NS. Biomater. Res. 2016; 20: 18
      CrossrefPubMed
    • 5b Wei T, Zhou Y, Zhan W, Zhang Z, Zhu X, Yu Q, Chen H. Colloids Surf., B 2017; 159: 527
      CrossrefPubMed
    • 5c Trachsel L, Romio M, Grob B, Zenobi-Wong M. ACS Nano 2020; 14: 10054
      CrossrefPubMed
    • 5d Shin E, Lim C, Kang UJ, Kim M, Park J, Kim D, Choi W, Hong J, Lee DW, Kim BS. Macromolecules 2020; 53: 3551
      CrossrefPubMed
  • 6 Synthetic procedure for compound 1: Ethylene glycol (dehydrated) 2.48 g (40 mmol) and pyridine 7.26 mL (90 mmol) were dissolved in dry THF 60 mL and cooled to 0 °C. Then, 2-bromopropanoyl bromide 9.43 mL (90 mmol) was diluted with dry THF 10 mL and added dropwise to the mixture and reacted at RT for 15 h. The resultant mixture was concentrated in vacuo and 100 mL of hexane/ethyl acetate (v/v = 1/1) mixture solution was added. The solution was washed with sat. sodium hydrogen carbonate aqueous solution 100 mL × 5, 1 M sodium hydrogen sulfate aqueous solution 100 mL × 3, and water 100 mL × 3. An organic layer was collected and dried over magnesium sulfate anhydrous. The solvents were removed in vacuo to give an objective ethane-1,2-diyl bis(2-bromopropanoate), 1, as a colorless oil (10.12 g, 76.2%). 1 H NMR [400 MHz, CDCl3, tetramethylsilane (TMS)] (Figure S1a): σ = 1.85 ppm ((–CH2OC(=O)CH(CH 3)Br)2 d, 6H), 4.40 ppm ((–CH2OC(=O)CH(CH3)Br)2 q, 2 H), 4.43 ppm ((–CH 2OC(=O)CH(CH3)Br)2 s, 4 H). 13 C NMR [75 MHz, CDCl3, TMS] (Figure S1b): σ = 21.6 ppm ((–CH2OC(=O)CH(CH3)Br)2), 39.6 ppm ((–CH2OC(=O)CH(CH3)Br)2), 63.3 ppm ((–CH2OC(=O)CH(CH3)Br)2), 170.1 ppm ((–CH2OC(=O)CH(CH3)Br)2
    PubMed
  • 7 Synthetic procedure for compound 2: Sodium hydride 6.68 g (0.167 mol) was dispersed to dry diethyl ether 200 mL and cooled to 0 °C under an argon gas atmosphere. Ethanethiol 13.3 mL (0.185 mol) was added dropwise to the dispersion solution and its mixture was stirred for 15 min. Then, carbon disulfide 11.2 mL (0.185 mol) was added and reacted at RT for 1 h. After reaction, the reaction mixture was added n-pentane 100 mL to precipitate a resultant sodium salt of trithiocarbonate. The precipitation was collected by filtration and washed with n-pentane 400 mL to give an objective sodium ethyl carbonotrithioate, 2, as a yellow powder (25.0 g, 93.4%). 1 H NMR [400 MHz, DMSO-d 6, TMS] (Figure S2a): σ = 1.14 ppm (CH 3CH2SC(=S)SNa, t, 3 H), 2.96 ppm (CH3CH 2SC(=S)SNa, q, 2 H). 13 C NMR [100 MHz, DMSO-d 6, TMS] (Figure S2b): σ = 14.6 ppm (CH3CH2SC(=S)SNa), 34.3 ppm (CH3 CH2SC(=S)SNa), 240.1 ppm (CH3CH2SC(=S)SNa)
    PubMed
  • 8 Synthetic procedure for compound 3: 7.6 g of 1 (47.4 mmol) and freshly prepared 3.2 g of 2 (9.5 mmol) were dissolved to acetonitrile 30 mL and stirred at RT for 1.5 days. The reaction mixture was added diethyl ether 200 mL and washed with water 200 mL × 4. An organic layer was collected and dried over magnesium sulfate anhydrous. The solution was concentrated to give an objective ethane-1,2-diyl bis(2-(((ethylthio)carbonothioyl)thio)propanoate, 3, as an orange oil (3.6 g, 92.1%). 1 H NMR [400 MHz, CDCl3, TMS] (Figure S3a): σ = 1.26 ppm ((–CH2OC(=O)CH(CH3)SC(=S)S–CH2CH 3 2 t, 6 H), 1.54 ppm ((–CH2OC(=O)CH(CH 3)SC(=S)SCH2CH3 2 t, 6 H), 3.29 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH 2CH3 2 q, 4 H), 4.28 ppm ((–CH 2OC(=O)CH(CH3)SC(=S)S–CH2CH3 2 s, 4 H), 4.77 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH2CH3 2 q, 2 H). 13 C NMR [100 MHz, CDCl3, TMS] (Figure S3b): σ = 12.7 ppm ((–CH2OC(=O)CH(CH3)SC(=S)S–CH2 CH3 2), 16.8 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH2CH3 2), 31.6 ppm ((–CH2OC(=O)CH–(CH3)SC(=S)SCH2CH3 2), 47.9 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH2CH3 2), 63.1 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH2CH3 2), 170.9 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH2–CH3 2), 221.9 ppm ((–CH2OC(=O)CH(CH3)SC(=S)SCH2CH3 2
    PubMed
  • 9 Synthetic procedure for compound 4: MEA 5.00 g (38.40 mmol), 3 17.15 mg (3.48 µmol), and AIBN 5.50 mg (3.48 µmol) were dissolved to toluene (monomer concentration: 4 M), and the solution was degassed over freeze–pump–thaw cycles (three times) under an argon gas atmosphere. Then the reaction mixture was placed in a preheated oil bath at 60 °C. After polymerization for 1 h, the mixture was cooled to RT and poured into a large excess of hexane to precipitate the resulting polymer. The polymer was further purified by a reprecipitation method from the THF/hexane system. The solvents were removed in vacuo to give a pure telechelic PMEA, 4, as a yellow-colored viscosity liquid (Conv.: 77.6%). 1 H NMR [400 MHz, CDCl3, TMS] (Figure 1b, black): σ = 1.26–3.0 ppm (–SC(=S)SCH2CH 3 t, 6 H (both end); –(CH 3)CH(=O)OCCH2CH2OC(=O)CH(CH 3)–, t, 6H; PMEA, methylene (main chain), 2(1–x nH; PMEA, methine (main chain), (1–x nH), 3.26–3.47 ppm (–SC(=S)SCH 2CH3 q, 4 H (both end); –CO(=O)CH2CH2OCH 3, 3(1–x nH), 3.48–3.70 ppm (–CO(=O)CH2CH 2OCH3, 2(1–x nH), 4.00–4.47 ppm (–(CH3)CH(=O)OCCH 2CH 2OC(=O)CH(CH3)–, s, 4 H; –CO(=O)CH 2CH2O–CH3, 2(1–x nH), 4.77 ppm (–(CH3)CH(=O)OCCH2CH2OC(=O)CH(CH3)–, q, 2 H). SEC [THF, 40 °C, PSt standard] (Figure 1a, black): M n,SEC = 76,300 g mol −1, Ð M w/M n) = 1.06
    PubMed
  • 10 Kujawa P, Segui F, Shaban S, Diab C, Okada Y, Tanaka F, Winnik FM. Macromolecules 2006; 39: 341
    CrossrefPubMed
      • 11
    • 11a Chong YK, Moad G, Rizzardo E, Thang SH. Macromolecules 2007; 40: 4446
      CrossrefPubMed
    • 11b Willcock H, O'Reilly RK. Polym. Chem. 2010; 1: 149
      PubMed
  • 12 Synthetic procedure for compound 5: 4 1.0 g (13.1 µmol), TTMSS 65. 1 mg (262.0 µmol), and V-70 2.0 mg (6.5 µmol) were dissolved to toluene 5 mL. The colored solution was deoxygenated by freeze–pump–thaw cycles (three times). Then the reaction mixture was stirred at 40 °C for 12 h, resulting in a colorless solution. The solution was poured into a large excess of hexane to precipitate an objective polymer. The polymer was further purified by a reprecipitation method from the THF/hexane system to give a pure desulfurized-PMEA, 5, as a colorless viscosity liquid (0.88 g). 1 H NMR [400 MHz, CDCl3, TMS] (Figure 1b, red): σ = 1.30–3.0 ppm (–(CH 3)CH(=O)OCCH2–CH2OC(=O)CH(CH 3)–, t, 6 H; PMEA, methylene (main chain), 2(1–x nH; PMEA, methine (main chain), (1–x nH), 3.26–3.47 ppm (–CO(=O)CH2CH2OCH 3, 3(1–x nH), 3.48–3.70 ppm (–CO(=O)CH2CH 2OCH3, 2(1–x nH), 4.00–4.47 ppm (–(CH3)CH(=O)OCCH 2CH 2OC(=O)CH–(CH3)–, s, 4 H; –CO(=O)CH 2CH2OCH3, 2(1–x nH), 4.77 ppm (–(CH3)CH(=O)OCCH2CH2O–C(=O)CH(CH3)–, q, 2 H). SEC [THF, 40 °C, PSt standard] (Figure 1a, red): M n = 75,900 g mol −1, Ð = 1.09
    PubMed
  • 13 Synthetic procedure for compounds 6 and 7: 4 1.0 g (13.1 µmol) and isobutylamine 95.9 mg (1.3 mmol) were dissolved in 20 mL THF and stirred at RT for 2 h, resulting in a colorless solution. The solution was poured into a large excess of hexane to precipitate an objective polymer. The polymer was further purified by a reprecipitation method from the THF/hexane system to give a pure thiol-terminated PMEA, 6, as a colorless viscous liquid (0. 67 g). Subsequently, 6 100 mg (1.31 µmol) was dissolved in 2 L of diethyl ether/THF (v/v = 3/1), and then iron(III) chloride 0.93 g (5.24 mmol) was added and stirred at RT for 1 month. The reaction mixture was concentrated in vacuo and poured into hexane to precipitate a resultant polymer as a yellowish viscous liquid. The polymer was passed through an alumina column using THF as an eluent. The solvents were removed in vacuo to obtain an objective cyclic PMEA, 7, as a colorless, viscous solid (38 mg). 1 H NMR [400 MHz, CDCl3, TMS] (Figure S5): σ = 1.30–3.0 ppm (–(CH 3)CH(=O)OCCH2–CH2OC(=O)CH(CH 3)–, t, 6 H; PMEA, methylene (main chain), 2(1–x nH; PMEA, methine (main chain), (1–x nH), 3.26–3.47 ppm (–CO(=O)CH2CH2OCH 3, 3(1–x nH), 3.48–3.70 ppm (–CO(=O)CH2CH 2OCH3, 2(1–x nH), 4.00–4.47 ppm (–(CH3)CH(=O)OCCH 2CH 2OC(=O)CH–(CH3)–, s, 4 H; –CO(=O)CH 2CH2OCH3, 2(1–x nH), 4.77 ppm (–(CH3)CH(=O)OCCH2CH2O–C(=O)CH(CH3)–, q, 2 H). SEC [THF, 40 °C, PSt standard] (Figure 2, violet): M p,L = 88,200 g mol −1, M p,C = 63,500 g mol −1, Ð = 1.27
    PubMed
      • 14
    • 14a Wang Z, He J, Tao Y, Yang L, Jiang H, Yang Y. Macromolecules 2003; 36: 7446
      CrossrefPubMed
    • 14b Llauro MF, Loiseau J, Boisson F, Delolme F, Ladavière C, Claverie J. J. Polym. Sci., Part A: Polym. Chem. 2004; 42: 5439
      PubMed
    • 14c Scales CW, Convertine AJ, McCormick CL. Biomacromolecules 2006; 7: 1389
      CrossrefPubMed
      15
    • 15a Whittaker MR, Goh Y.-K, Gemici H, Legge TM, Perrier S, Monteiro MJ. Macromolecules 2006; 39: 9028
      CrossrefPubMed
    • 15b Laurent BA, Grayson SM. Chem. Soc. Rev. 2009; 38: 2202
      CrossrefPubMed
    • 15c Stamenović MM, Espeel P, Baba E, Yamamoto T, Tezuka Y, Prez FE. D. Polym. Chem. 2013; 4: 184
      PubMed
      16
    • 16a Roovers JE. L, Toporowski PM. Macromolecules 1983; 16: 843
      CrossrefPubMed
    • 16b Lepoittevin B, Dourges MA, Masure M, Hemery P, Baran K, Cramail K. Macromolecules 2000; 33: 8218
      CrossrefPubMed
    • 16c Takano A, Kushida Y, Aoki K, Masuoka K, Hayashida K, Cho D, Kawaguchi D, Matsushita Y. Macromolecules 2007; 40: 679
      CrossrefPubMed
    • 16d Jeong Y, Jin Y, Chang T. Macromolecules 2017; 50: 7770
      CrossrefPubMed
      17
    • 17a Clarson SJ, Semlyen JA. Polymer 1986; 27: 1633
      CrossrefPubMed
    • 17b Yamamoto T, Tezuka Y. Polym. Chem. 2011; 2: 1930
      PubMed
    • 17c Jia Z, Monteiro MJ. J. Polym. Sci., Part A: Polym. Chem. 2012; 50: 2085
      PubMed
    • 17d Gao L, Oh J, Tu Y, Chang T, Li CY. Polymer 2019; 170: 198
      CrossrefPubMed
      18
    • 18a Reimschuessel HK, Turi EA, Akkapeddi MK. J. Polym. Sci., A: Polym. Chem. 1979; 17: 2769
      PubMed
    • 18b Drake AC, Lee Y, Burgess EM, Karlsson JO. M, Eroglu A, Higgins AZ. PLoS One 2018; 13: e0190713
      CrossrefPubMed
      19
    • 19a Magerl D, Philipp M, Qiu X.-P, Winnik FM, Muller-Buschbaum P. Macromolecules 2015; 48: 3104
      CrossrefPubMed
    • 19b Yan W, Divandari M, Rosenboom J.-G, Ramakrishna SN, Trachsel L, Spencer ND, Morgese G, Benetti EM. Polym. Chem. 2018; 9: 2580
      PubMed
      20
    • 20a Kittaka S, Ueda Y, Fujisaki F, Iiyama T, Yamaguchi T. Phys. Chem. Chem. Phys. 2011; 13: 17222
      CrossrefPubMed
    • 20b Cuadrado-Collados C, Majid AA. A, Martínez-Escandell M, Daemen LL, Missyul A, Koh C, Silvestre-Albero J. Carbon 2020; 158: 346
      CrossrefPubMed
      21
    • 21a Zimm BH, Stockmayer WH. J. Chem. Phys. 1949; 17: 1301
      CrossrefPubMed
    • 21b Jang SS, Cagin T, Goddard WA. J. Chem. Phys. 2003; 119: 1843
      CrossrefPubMed
    • 21c Magerl D, Philipp M, Metwalli E, Gutftreund P, Qiu XP, Winnik FM, Muller-Buschbaum P. ACS Macro Lett. 2015; 4: 1362
      CrossrefPubMed
      22
    • 22a Murakami D, Kobayashi S, Tanaka M. ACS Biomater. Sci. Eng. 2016; 2: 2122
      CrossrefPubMed
    • 22b Murakami D, Kitahara Y, Kobayashi S, Tanaka M. ACS Biomater. Sci. Eng. 2018; 4: 1591
      PubMed
    • 22c Ueda T, Murakami D, Tanaka M. Front. Chem. 2018; 6: 542
      CrossrefPubMed
    • 22d Ueda T, Murakami D, Tanaka M. Colloids Surf., B 2021; 199: 1115
      PubMed
  • 23 Hirata T, Matsuno H, Kawaguchi D, Yamada NL, Tanaka M, Tanaka K. Phys. Chem. Chem. Phys. 2015; 17: 17399
    CrossrefPubMed