PDF icon PDF herunterladen
J Knee Surg 2023; 36(06): 596-604
DOI: 10.1055/s-0041-1740392
Original Article

Biomechanical Comparison of Kinematic and Mechanical Knee Alignment Techniques in a Computer Simulation Medial Pivot Total Knee Arthroplasty Model

Young Dong Song
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Shinichiro Nakamura
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Shinichi Kuriyama 
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Kohei Nishitani
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Hiromu Ito
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
2   Department of Advanced Medicine for Rheumatic Diseases, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Yugo Morita
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Yusuke Yamawaki
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
,
Shuichi Matsuda
1   Department of Orthopaedic Surgery, Graduate School of Medicine, Kyoto University, Kyoto, Japan
› Institutsangaben
› Weitere Informationen
   Lizenzen und Reprints
Preview

Abstract

Several concepts may be used to restore normal knee kinematics after total knee arthroplasty. One is a kinematically aligned (KA) technique, which restores the native joint line and limb alignment, and the other is the use of a medial pivot knee (MPK) design, with a ball and socket joint in the medial compartment. This study aimed to compare motions, contact forces, and contact stress between mechanically aligned (MA) and KA (medial tilt 3° [KA3] and 5° [KA5]) models in MPK. An MPK design was virtually implanted with MA, KA3, and KA5 in a validated musculoskeletal computer model of a healthy knee, and the simulation of motion and contact forces was implemented. Anteroposterior (AP) positions, mediolateral positions, external rotation angles of the femoral component relative to the tibial insert, and tibiofemoral contact forces were evaluated at different knee flexion angles. Contact stresses on the tibial insert were calculated using finite element analysis. The AP position at the medial compartment was consistent for all models. From 0° to 120°, the femoral component in KA models showed larger posterior movement at the lateral compartment (0.3, 6.8, and 17.7 mm in MA, KA3, and KA5 models, respectively) and larger external rotation (4.2°, 12.0°, and 16.8° in the MA, KA3, and KA5 models, respectively) relative to the tibial component. Concerning the mediolateral position of the femoral component, the KA5 model was positioned more medially. The contact forces at the lateral compartment of all models were larger than those at the medial compartment at >60° of knee flexion. The peak contact stresses on the tibiofemoral joint at 90° and 120° of knee flexion were higher in the KA models. However, the peak contact stresses of the KA models at every flexion angle were <20 MPa. The KA technique in MPK can successfully achieve near-normal knee kinematics; however, there may be a concern for higher contact stresses on the tibial insert.

Keywords

total knee arthroplasty - computer simulation - medial pivot knee - kinematics - contact stresses


Publikationsverlauf

Eingereicht: 29. Mai 2021

Angenommen: 22. Oktober 2021

Artikel online veröffentlicht:
10. Dezember 2021

© 2021. Thieme. All rights reserved.

Thieme Medical Publishers, Inc.
333 Seventh Avenue, 18th Floor, New York, NY 10001, USA